Rastergraf Eclipse3 Series Manual do Utilizador descarregar pdf (Página 44)

Rastergraf

2-12 Installing Your Peritek Graphics Board

Caution

The static electricity that your body builds up normally can seriously

damage the components on the graphics board.

3. Wear a grounded wrist strap and touch a metal part of the computer

chassis. Remove the card slot blocking plate from the chassis. Then,

remove the graphics board from its anti static bag, and immediately

slide it into the slot.

Figure 2-6 Installation of a PCI Module into an Emerson MTX

4. After making sure the board is seated correctly, install the screw into

the place where the blocking plate was and which (now) holds the

graphics board’s front panel

5. Close the computer.

Now, go to Section 2.7

1 2 ... 39 40 41 42 43 44 45 46 47 48 49 ... 84 85

Eclipse3 Series 1
User’s Manual 1
Table of Contents 2
Figures and Tables 3
Introduction 5
Getting Help 6
Board Revisions 6
Notices 7
Introduction - 4 8
Chapter 1 9
General Information 9
1.2 Functional Description 10
Rastergraf 11
General Information 1-3 11
1-4 General Information 12
1.2.2 DVI Digital Output 13
1.2.3 Software Support 13
Host PCI Bus 14
1.3 Additional References 15
1-8 General Information 16
General Information 1-9 17
1-10 General Information 18
General Information 1-11 19
1-12 General Information 20
1-14 General Information 22
1.5.1 VGA Connector 23
1-16 General Information 24
1.5.2 DVI-I Connector 25
1-18 General Information 26
General Information 1-19 27
1-20 General Information 28
A B C D E 29
Z A B C D E F 30
1.6 Monitor Requirements 31
1-24 General Information 32
Chapter 2 33
Installing Your Peritek 33
Graphics Board 33
2.2 Unpacking Your Board 34
2.3.1 Interrupt Settings 35
2.3.2 Address Settings 35
2.3.3 Changing the Jumpers 36
PMC Slot 1 40
PMC Slot 0 40
Now, go to Section 2.7 41
2.7.2 Checking your Display 48
2.8.1 Multiboard Operation 49
2.9.1 Multiboard Operation 52
2.11 Final Checks 57
Chapter 3 59
Programming On-board 59
Devices 59
3.2.1 Introduction 61
3.2.2 Host Bus Interface 61
3.2.3 Frame Buffer 61
Block Diagram 62
3.2.5 Drawing Engine 63
3.2.7 CRT Controller 64
3.2.8 Memory Controller 64
3.2.9 VGA Core 64
(1279,0) 66
(0,1023) (1279,1023) 66
3.3 Borealis Clocks 68
3.6 Video Timing Parameters 71
Horizontal Border 73
Horizontal Blank 73
Horizontal Retrace 73
3.6.2 Pan and Scroll 74
3.8 Talk To Me Through I 77
2 79
79
3.10 Flash EEPROM 80
3.11 Serial EEPROM 80
3.12 Interrupts 80
Chapter 4 81
Troubleshooting 81
4.1 General Procedures 82
Maintenance 83
Warranty 83
Return Policy 84
Out of Warranty Service 84

Comentários a estes Manuais

Sem comentários

Rastergraf Eclipse3 Series Manual do Utilizador Página 44

Comentários a estes Manuais